PIER Letters
 
Progress In Electromagnetics Research Letters
ISSN: 1937-6480
Home | Search | Notification | Authors | Submission | PIERS Home | EM Academy
Home > Vol. 60 > pp. 101-106

CHARACTERISATION OF COPPER NANOPARTICLE INK PRINTED FSS FOR CELLULAR SIGNALS SUPPRESSION

By F. C. Seman, N. K. b. A. Khalid, and S. b. M. Said

Full Article PDF (489 KB)

Abstract:
This paper proposes a copper nanoparticle inkprinted frequency selective surface (FSS) for cellular signals suppression. The FSS pattern is deposited on a polyimide film by using an inkjet printing technique. The printed FSS elements undergo the post-processing called sintering,where the optimum exposure duration and temperature are determined in order to form a conductive path across the metal pattern. Later, the conductivity of the printed FSS structure deposited on polyimide film is observed. The signal suppression ability of the printed FSS is conducted using the Computer Simulation Technology (CST) Microwave Studio software.

Citation:
F. C. Seman, N. K. b. A. Khalid, and S. b. M. Said, "Characterisation of Copper Nanoparticle Ink Printed FSS for Cellular Signals Suppression," Progress In Electromagnetics Research Letters, Vol. 60, 101-106, 2016.
doi:10.2528/PIERL16030108

References:
1. Zhou, Y., et al., "An overview on intercell interference management in mobile cellular networks from 2G to 5G," IEEE International Conference on Communication Systems (ICCS), 217-221, Nov. 19-21, 2014.

2. Mishra, N. K., "Development of GSM-900 mobile jammer: An approach to overcome existing limitation of jammer," 5th IEEE Conference on Wireless Communication and Sensor Networks (WCSN), 1-4, Dec. 15-19, 2009.

3. Pasian, M., et al., "Accurate modeling of dichroic mirrors in beam-waveguide antennas," IEEE Trans. Antennas and Propag., Vol. 61, No. 4, 1931-1938, Apr. 2013.
doi:10.1109/TAP.2012.2231928

4. Zhao, J. and X. Xu, "Study of the effect of a finite FSS radome on a horn antenna," IEEE International Conference on Microwave Technology and Computational Electromagnetics (ICMTCE), 74-76, 2011.

5. Sung, G. H. H., et al., "A frequency-selective wall for interference reduction in wireless indoor environments," IEEE Antennas and Propag. Mag., Vol. 48, No. 5, 29-37, 2006.
doi:10.1109/MAP.2006.277152

6. Parker, E. A., et al., "Frequency selectively screened office incorporating convoluted FSS window," Electron. Letters, Vol. 46, No. 5, 317-318, Mar. 2010.
doi:10.1049/el.2010.2530

7. Khalid, N. K. and F. C. Seman, "Characterisation of electrical conductivity of silver printed FSS for cellular signals suppression," 2015 IEEE International RF and Microwave Conference (RFM), Dec. 2015.

8. Khalid, N. K. and F. C. Seman, "Double square loop Frequency Selective Surface (FSS) for GSM shielding," International Conference on Communication and Computer Engineering (ICOCOE), Vol. 315, 223-229, May 2014.

9., "Malaysian communications and multimedia commission," Spectrum Allocation, [Online] Available: http://www.skmm.gov.my/Spectrum/Spectrum-Allocation-List/Spectrum-Allocation.aspx.

10. Jang, S., et al., "Sintering of inkjet printed copper nanoparticles for flexible electronics," Scripta Materialia, Vol. 62, 258-261, Mar. 2010.
doi:10.1016/j.scriptamat.2009.11.011

11. Halonen, E., et al., "The effect of laser sintering process parameters on Cu nanoparticle ink in room conditions," Optics and Photonics Journal, Vol. 3, 40-44, 2013.
doi:10.4236/opj.2013.34A007

12. Kim, J., et al., "Characterization of copper conductive ink for low temperature sintering processing on flexible polymer substrate," 16th IEEE Electronics Packaging Technology Conference (EPTC), 27-30, Dec. 2014.
doi:10.1109/EPTC.2014.7028308

13. Niittynen, J. and M. Mantysalo, "Characterization of laser sintering of copper nanoparticle ink by FEM and experimental testing," IEEE Trans. on Components, Packaging and Manufacturing Technology, Vol. 4, No. 12, 2018-2025, Dec. 2014.
doi:10.1109/TCPMT.2014.2363032

14. Kang, J. S., et al., "Inkjet printed electronics using copper nanoparticle ink," Journal of Materials Science: Materials in Electronics, 1213-1220, 2010.
doi:10.1007/s10854-009-0049-3

15. Niittynen, J., et al., "Comparison of laser and intense pulsed light sintering (IPL) for inkjet-printed copper nanoparticles layers," Scientific Reports, 2015.

16. Jun, S., et al., "3D printing technique for the development of non-planar electromagnetic bandgap structures for antenna applications," Electronics Letters, Vol. 52, No. 3, 175-176, Feb. 2016.
doi:10.1049/el.2015.3637

17. Seman, F. C., et al., "Design of a salisbury screen absorber using frequency selective surfaces to improve bandwidth and angular stability performance," IET Microwaves, Antennas & Propagation, Vol. 5, No. 2, 149-156, Jan. 31, 2011.
doi:10.1049/iet-map.2010.0072


© Copyright 2010 EMW Publishing. All Rights Reserved