A novel printed monopole antenna for ultra-wideband (UWB) applications is presented, which is composed of wide slot and Y-shaped microstrip feed line with a pair of inverted-L-shaped notches. The prototype with an overall size of 26 mm × 30 mm × 2 mm achieves good impedance matching, constant gain, stable radiation patterns, and a relative impedance bandwidth of 110.6% is achieved, which covers 3.09-10.74 GHz.

A thermal analysis and structure of a ridge single mode waveguide with a metal heater are presented. The steady-state temperature increases linearly and the thermal response becomes slower at the same power consumption, when the under-etched depth in the lower cladding increases. When the upper cladding thickness decreases, the thermal response becomes faster. This shows that a thinner upper cladding and a deeper etching are preferred to achieve a faster thermal response and lower power consumption, respectively. The numerical simulation also shows the power consumption of the present ridge waveguide is almost third of that for conventional one and the response time is half of that of the conventional one.

Models based on fuzzy inference systems (FISs) for calculating the resonant frequency of rectangular microstrip antennas (MSAs) with thin and thick substrates are presented. Two types of FIS models, Mamdani FIS model and Sugeno FIS model, are used to compute the resonant frequency. The parameters of FIS models are determined by using various optimization algorithms. The resonant frequency results predicted by FIS models are in very good agreement with the experimental results available in the literature. When the performances of FIS models are compared with each other, the best result is obtained from the Sugeno FIS model trained by the leastsquares algorithm.

In this paper, frequency selective surfaces (FSSs) are analyzed and designed. The analytical procedure is based on method of moments (MoM). The generalized minimal residual recursive method combined with fast Fourier transform (GMRESR-FFT) is utilized to accelerate the solution of the matrix equation. Our numerical results show that the GMRESR-FFT method can converge at least 3 times faster than the generalized minimal residual fast Fourier transform method (GMRES-FFT). In this paper, the cross dipoles are first used to design the FSS filter with a passband at 300 GHz and a stopband at 450 GHz, and then the Jerusalem cross slots are utilized to avoid grating lobes and improve the bandwidth of FSS. Numerical results demonstrate the validity and efficiency of the presented method.

This paper introduces a planar μ-negative (MNG) metamaterial structure, called double-sided split ring resonator (DSRR), which combines the features of a conventional SRR and a broadside-coupled SRR (BC-SRR) to obtain much better miniaturization at microwave frequencies for a given physical cell size. In this study, electromagnetic transmission characteristics of DSRR, BC-SRR and conventional SRR are investigated in a comparative manner for varying values of substrate parameters which are thickness, the real part of relative permittivity and dielectric loss tangent. Simulation results have shown that magnetic resonance patterns of all these three structures are affected in a similar way from variations in permittivity and in loss tangent. However, changes in substrate thickness affect their resonance characteristics quite differently: In response to decreasing substrate thickness, resonance frequency of the SRR increases slowly while the bandwidth and the depth of its resonance curve do not change much. For the DSRR and BCSRR structures, on the other hand, resonance frequency, half power bandwidth and the depth of resonance curve strongly decrease with decreasing substrate thickness. Among these three structures, all having the same unit cell dimensions, the newly suggested DSRR is found to reach the lowest resonance frequency, hence the smallest electrical size, which is a highly desired property not only for more effective medium approximation but also for miniaturization in RF design. The BC-SRR, on the other hand, provides the largest resonance bandwidth which is almost three times of the resonance bandwidth of the SRR. The bandwidth of the DSRR approaches to that of the BC-SRR as the planar separation between its inner and outer rings increases.

The plane wave diffraction by a terminated, semi-infinite parallel-plate waveguide with four-layer material loading is rigorously analyzed using the Wiener-Hopf technique. Introducing the Fourier transform for the unknown scattered field and applying boundary conditions in the transform domain, the problem is formulated in terms of the simultaneous Wiener-Hopf equations satisfied by the unknown spectral functions. The Wiener-Hopf equations are solved via the factorization and decomposition procedure leading to the exact solution. The scattered field in the real space is evaluated by taking the inverse Fourier transform and using the saddle point method. Representative numerical examples of the radar cross section (RCS) are presented, and the far-field scattering characteristics of the waveguide are investigated in detail.

This paper presents an improvement of the calculation of the magnetic field components created by ring permanent magnets. The three-dimensional approach taken is based on the Coulombian Model. Moreover, the magnetic field components are calculated without using the vector potential or the scalar potential. It is noted that all the expressions given in this paper take into account the magnetic pole volume density for ring permanent magnets radially magnetized. We show that this volume density must be taken into account for calculating precisely the magnetic field components in the near-field or the far-field. Then, this paper presents the component switch theorem that can be used between infinite parallelepiped magnets whose cross-section is a square. This theorem implies that the magnetic field components created by an infinite parallelepiped magnet can be deducted from the ones created by the same parallelepiped magnet with a perpendicular magnetization. Then, we discuss the validity of this theorem for axisymmetric problems (ring permanent magnets). Indeed, axisymmetric problems dealing with ring permanent magnets are often treated with a 2D approach. The results presented in this paper clearly show that the two-dimensional studies dealing with the optimization of ring permanent magnet dimensions cannot be treated with the same precisions as 3D studies.

Light extraction efficiency of light-emitting diodes (LEDs) based on various photonic crystal (PhC) structures was investigated in this study. By using the plane wave method and the finite element method, the influence of several factors on the enhancement of light extraction was discussed, including lattice type, density of states from a photonic band diagram, ratio of cylinder radius and lattice constant, and thickness of a photonic crystal pattern. Some rules are given for the practical implementation of an optimized PhC-based LED with higher light extraction efficiency. In the simulation results, the maximum enhancement of the extraction efficiency could be found to be by a factor of approximately 2.8 for the optimized Archimedean tiling pattern in the LED device emitting at the center wavelength of 530 nm. However, with the use of optimized PhC structures, the square and triangular lattices reveal enhancements of ~1.7 and ~1.5, respectively. The extraction efficiency of the Archimedean PhC LED is much greater than that of the regular lattice PhC LED.

This paper presents a rhombic patch monopole antenna applied with a technique of fractal geometry. The antenna has multiband operation in that the generator model, which is an initial model to create a fractal rhombic patch monopole, is inserted at each center side of a rhombic patch monopole antenna. Especially, a modified ground plane has been employed to improve input impedance bandwidth and high frequency radiation performance. The proposed antenna is designed and implemented to effectively support personal communication system (PCS 1.85-1.99 GHz), universal mobile telecommunication system (UMTS 1.92-2.17 GHz), wireless local area network (WLAN), which usually operate in the 2.4 GHz (2.4-2.484 GHz) and 5.2/5.8 GHz (5.15-5.35 GHz/5.725-5.825 GHz) bands, mobile worldwide interoperability for microwave access (Mobile WiMAX), and WiMAX, which operate in the 2.3/2.5 GHz (2.305-2.360 GHz/2.5-2.69 GHz) and 5.5 GHz (5.25-5.85 GHz) bands. The radiation patterns of the proposed antennas are still similarly to an omnidirectional radiation pattern. The properties of the antenna such as return losses, radiation patterns and gain are determined via numerical simulation and measurement.

The effects of the surface slopes joint probability density, the shadowing function, the skewness of sea waves and the curvature of the surface on the backscattering from the ocean surface are discussed and an improved two-scale model modified by these four aspects is used to calculate the backscattering coefficient of the dynamic ocean surface. In order to deal with the surface skewness driven by wind, a new complementary term derived from the small perturbation method is included in the improved model, in which the Fourier transform of the third-order cumulant function, surface bispectrum, is employed. On this basis, with the oceanic whitecap coverage taken into account, a composite model for predicting the ocean surface backscattering coefficient is constructed tentatively, which incorporates the volume scattering into the total one. Finally, with the vector radiative transfer (VRT) theory employed, numerical illustrations are carried out for the backscattering coefficients versus wind speed, incidence angle and azimuth angle, respectively. The predictions of the composite model are verified in Ku- and Ka-bands through the comparison of numerical results with many sets of measured data and the aircraft measurement experiment carried out in ZHOUSHAN sea area also supports this model.

A novel artificial transmission line with right/left-handed behavior is presented in this paper. The unit cell of the new artificial line consists of one series and one shunt wire bonded interdigital capacitors. When wire bonded interdigital capacitors are used, the artificial line has a wider frequency band of operation. A combined analytical-graphical design method of the proposed artificial transmission line is also presented. The method has been assessed with the help of an electromagnetic solver based on the method of moments, and experimental work.

The adjoint variable method is applied for the first time to perform sensitivity analysis with transmission line modelingexploiting rubber cells. Rubber cells allow for the conformal modelingof off-grid boundaries in the transmission line modeling computational domain usingmo dified tensor properties. The scatteringmatrix of the rubber cell is analytically dependent on the dimensions of the modeled discontinuities. Usingthis property, an exact adjoint system is derived. The original and adjoint systems supply the necessary field information for the rubber cell based sensitivity calculations. Our technique is illustrated through sensitivity analysis of waveguide filters. The estimated sensitivities are used for fast gradient-based optimization and tolerance analysis.

An ultra wideband radar system based on a coherent emission of an Ultra-Wideband antenna array using photoconductive switching devices is proposed. The triggering process is obtained by excitation of semiconductor samples in linear mode using a picosecond laser source. The emitting antenna system and the receiving antenna developed by the research Institute XLIM, present some specific qualities suitable for radiation and measurement of ultra-short pulses. The optical control of the sources allows to sum the radiated power and to steer the transient radiation beam accurately. The experiments realized with this optoelectronic array validate these two concepts. An other way of improvement of these systems is proposed. It consists by using bipolar pulse generators.

This paper links the multipath smart antenna CDMA system signal detection problem to the PARAllel profiles with LINear Dependencies (PARALIND), and derives a deterministic blind PARALIND algorithm whose performance is very close to nonblind space-time minimum mean square error (ST-MMSE) method. The blind PARALIND algorithm has the better performance than spacetime matched filter. The proposed PARALIND algorithm also works well in array error condition. Most notably, it does not require knowledge of the DOA (Direction Of Arrival) and channel fading information.

One-dimensional ternary photonic crystals are suggested as refractometric sensing elements, for sensing very small refractive index changes of a medium. These one-dimensional ternary photonic crystals based refractometric sensing elements are not only remarkably smaller, but are also more sensitive than one-dimensional binary photonic crystal based sensing element recently suggested by researchers.

The optimization and simulated realization of planar 2-D antenna array with a flat-top shaped-beam pattern are proposed in this paper. The shaped-beam planar array can be used as an element of Very Large Array for the Deep Space Detection. A conventional genetic algorithm is chosen for the optimization. However, the synthesis of flat-top shaped-beam using a planar 2-D array is difficult because of the inherently large number of degrees of freedom involved in the algorithm (in generally, the amplitude and phase of each element must be determined). Therefore, a sub-array rotation method, which lies on the flat-top pattern synthesis itself, is proposed in this study to resolve the design problem. Besides, the proposed synthesis has taken the actual element patterns but identical and isotropic ones into account, which can reduce the error between computation and realization. A 8*8 (64)-element rectangular array is exampled, and the results of the optimized flat-top patterns are shown to illustrate the validity and high efficiency of the technique.

At WRC-07, the frequency band 3500 MHz has been allotted for the next generation of mobile International Mobile Telecommunication-Advanced (IMT-Advanced). Meanwhile this band is already in used by fixed services, which means that harmful interference probability may be transpired. In this paper, the coexistence between the two services in various geographical deployment areas (dense urban, urban, suburban, and rural areas) will be analyzed. Spectrum emission mask is an effective interference model will be invested and interference to noise ratio of -6 dB is the used coexistence criteria. Co-channel, zero-guard band, and adjacent channel are three Intersystem interference scenarios will be investigated. The analysis will focus on determine required minimum separation distance and frequency separation under different attenuation due to local clutter and height of antennas at fixed channel bandwidth.

In this research, a fast approach of method of moments (MoM) for analyzing 3-D dielectric body is proposed. The unknown polarization current in dielectric body is expanded into rectangular blocks with overlapping volume sinusoidal basis functions. To accelerate the matrix-solving CPU time in MoM, the multi-region iterative method, where the overlapping blocks are used as the iteration units, is applied to solving the matrix equation in the MoM. Some numerical results are given to show that the CPU time for solving unknown currents can be reduced effectively by multi-region iterative method.

Uncertainties in biological tissue properties are weighed in the case of a hyperthermia problem. Statistic methods, experimental design and kriging technique, and stochastic methods, spectral and collocation approaches, are applied to analyze the impact of these uncertainties on the distribution of the electromagnetic power absorbed inside the body of a patient. The sensitivity and uncertainty analyses made with the different methods show that experimental designs are not suitable in this kind of problem and that the spectral stochastic method is the most efficient method only when using an adaptative algorithm.

In this paper, a new Yagi-Uda substrate is proposed to obtain radar cross section (RCS) reduction. The Yagi-Uda substrate on which three kinds of metal microstrip lines are etched is put directly on the top of a patch antenna and can reduce RCS sharply by steering the direction of reflecting wave at resonant frequencies. Using a reconfiguration technique, the antenna can radiate without the substrate's effects. When the antenna does not need to work, the Yagi-Uda substrate works to reduce the RCS of the antenna. Besides, the resonant frequencies can be shifted by reconfiguring the Yagi-Uda substrate, so the RCS can be reduced in a broad frequency band.