Transient field of a high-altitude electromagnetic pulse (HEMP) induced near ground is simulated, of which the ground reflection can not be neglected. The Jefimenko's equation is applied to compute the incident electric field near the ground, attributed to both the primary and the secondary currents in the source region. The field-dependent air conductivity in the source region is obtained by solving three nonlinear governing equations iteratively, and the reflected field is computed in the frequency domain.

Planar gigahertz (GHz) inductors were fabricated based on high crystalline-anisotropy Zn_0.13Co_0.04Ni_0.63Fe_2.2O₄ (Zn-Co-Ni ferrite) and Ba₃Co₂Fe₂₄O₄₁ (Co₂Z hexaferrite) and characterized for inductance (L) and quality (Q) factor. The planar ferrite inductors show an L of 4.5 nH (Zn-Co-Ni), 5.6 nH (Zn-Co-Ni + low Hk and fFMR Co₂Z:), and 4.8 nH (Zn-Co-Ni + high Hk and fFMR Co₂Z:) at 2 GHz. The corresponding L-densities are 18.0, 22.4, and 19.2 nH/mm², which are greater than 16.8 nH/mm² of the air-core inductor. With respect to the Q factor, the air-core and ferrite inductors exhibit Q factors of 6.7 (air-core), 4.8 (Zn-Co-Ni), 2.8 (Zn-Co-Ni + low Hk Co₂Z), and 4.0 (Zn-Co-Ni + high Hk Co₂Z) at 2 GHz. The tan δμ of the ferrites caused a reduction in the Q factor. Nevertheless, the high Hk and fFMR Co₂Z ferrite inductor demonstrates a higher Q factor than that of the low Hk and fFMR Co₂Z inductor. It is, therefore, suggested that high-resistivity, -anisotropy, -magnetization ferrite can produce large L-density and Q-factor GHz inductors.

A low-profile three-current model is proposed to guide the design of an on-board antennas with a broad beam. Based on this model, an on-board three-element antenna is designed. When the side length of the ground is infinite, the 3-dB beamwidths in the xz plane and yz plane are all 180°, and the radiation pattern in the xy plane has a gain fluctuation less than 3 dB. When the side length of the ground is 2λ, the measured 3-dB beamwidths in the xz plane and yz plane are 141° and 148°, respectively. A quasi-hemispherical radiation pattern can be obtained based on the proposed three-current model.

The electromagnetic passive localization without the need of carrying any device, named device-free passive localization (DFPL) technique, is an emerging technology for determining an uncooperative target's position. The DFPL technique detects the shadowed links in a monitored area and realizes localization with the received signal strength (RSS) measurements of these links. However, most current RSS-based DFPL schemes belong to the model-based DFPL method, since the localization accuracy depends on the shadowing model. Moreover, model-based DFPL methods require high memory and computing resources for accurate tracking performance, and thus may not be suitable for resource-constrained applications. To overcome these problems, in this paper we propose a lightweight DFPL method which makes use of recent link lines detected by wireless sensor networks to estimate the target's location. This method can be independent of the shadowing model and can also reduce the algorithm's storage and computational resource requirements. The effectiveness and robustness of the proposed scheme are demonstrated by experimental results where the proposed algorithm yields substantial improvement for localization performance and complexity.

A compact wideband antenna consisting of a L-shaped radiating element which has a modified inverted-F structure and a C-shaped parasitic radiating element on the ground is proposed. Three resonant frequencies and a very wide operating band are obtained. A prototype of the proposed antenna has been constructed and experimentally studied. The measured results show that the operating bandwidth with 10 dB return loss is about 2.9 GHz (2.11-5.01 GHz), 81.46%, respectively, covering LTE2500 (2.5-2.69 GHz), 2.4 GHz WLAN and 2.5/3.5 GHz WiMAX bands. Furthermore, the antenna has a simple planar structure and small volume of only 30 × 30 × 1.6 mm³. Good radiation characteristics and acceptable peak gains are obtained over the operating bands.

The frequency-modulated continuous wave (FMCW) synthetic aperture radar (SAR) has the properties of compact size, lightweight, low cost and low power dissipation, which provides great potential in the application of small platforms such as unmanned aerial vehicle (UAV). The imaging characteristics of rotary target for FMCW SAR are analysed based on the construction of echo signal model. Further, a passive suppressing jamming method for FMCW SAR based on micromotion modulation is proposed. This method makes use of rotary corner reflector to form jamming strips in range and azimuth, and then the target screened is protected effectively. The choice of parameters of rotary corner reflectors is discussed in detail. Finally, some simulations are given to validate the theoretical derivation and the effectiveness of method.

The aim of this study is to present a dual-band antenna for Wireless Medical Telemetry Service (WMTS) applications. The antenna covers all three frequency bands 608-614 MHz, 1395-1400 MHz, and 1427-1432 MHz, and is intended for continuous health monitoring of patient's vital parameters. The designed antenna consists of a meandered dipole antenna and a superstrate layer to preserve the biocompatibility of the structure. It has a compact size with dimensions 17.6 mm x 12 mm x 2.54 mm. The measured -10 dB bandwidths are found to be 16.3% for the lower frequency band and 10.6% in the upper frequency band. The antenna is in vitro tested in a tissue mimicking solution.

The study of earth terrain in Antarctica is important as this region has a direct impact on global environment and weather condition. There have been many research works in developing remote sensing technologies, as it can be used as an earth observation technique to monitor the polar region (Giles et al., 2009; Park et al., 2012). In previous studies, remote sensing forward model has been developed to study and understand scattering mechanisms and sensitivity of physical parameters of snow and sea ice. This paper is an extended work from previous studies (Syahali et al., 2011; Syahali, 2012; Syahali and Ewe, 2012, 2013), where an improved theoretical model to study polar region was developed. Multiple-surface scattering, based on an existing integral equation model (IEM) that calculates surface scattering and additional second-order surface-volume scattering, were added in the model from prior research works (Ewe et al., 1998) for improvement in the backscattering calculation. We present herein the application of this model on a snow layer above ground which is modeled as a volume of ice particles that are closely packed and bounded by irregular boundaries above a homogenous half space. The effect of including multiple surface scattering and additional surface-volume scattering up to second order in the backscattering coefficient calculation of snow layer is studied for co-polarized and cross-polarized returns. Comparisons with satellite data are also done for validation. Results show improvement in the total backscattering coefficient for cross-polarized return in the studied range, suggesting that multiple-surface scattering and surface-volume scattering up to second order are important scattering mechanisms in the snow layer and should not be ignored in polar research.

This paper presents a new hybridization between MoM-GEC and a MultiResolution analysis (MR) based on the use of wavelets functions as trial functions. The proposed approach is developed to speed up convergence, alleviate calculation and then provide a considerable gain in requirements (processing time and memory storage) because it generates a sparse linear system. The approach consists in calculating the total current and input impedance on an invariant metallic pattern through two steps. The first one consists in expressing the boundary conditions of the unknown electromagnetic current with a single electrical circuit using the Generalized Equivalent Circuit method (GEC) and then deduce an electromagnetic equation based on the impedance operator. The impedance operator used here is described using the local modal basis of the waveguide enclosing the studied structure. The second step consists in approximating the total current using orthonormal periodic wavelets as testing functions and the local modal basis of the waveguide as basis functions. The proposed approach allows fast calculation of such inner products through the use of the wavelets multiresolution (MR) analysis advantages, thus significantly reducing the required CPU-time for microstrip-type structure analysis [13, 14]. A sparse matrix is generated from the application of a threshold. A sparsely filled matrix is easier to store and invert [15, 16]. Based on this approach, we study the planar structures. The obtained results show good accuracy with the method of moments. Moreover, we prove considerable improvements in CPU time and memory storage achieved by the MR-GEC approach when studying these structures.

A hybrid algorithm based on the invasive weed optimization (IWO) and the convex optimization (CVX) is proposed for minimizing the peak sidelobe level (PSLL) of linear array with focused and/or shaped beam pattern. In this approach, IWO is adopted to produce the array (described by element positions), and CVX is used to determine the excitations for each produced array. Then the corresponding PSLL acts as the fitness function of IWO to find the optimal positions which lead to the minimum PSLL. Numerical experiments are conducted to validate the effectiveness and robustness of the proposed hybrid approach. Compared with other techniques, a lower PSLL can be achieved with a fixed main beam width or with a shaped main beam using this hybrid algorithm. Moreover, this method can easily cope with some constraints on the aperture, such as the minimum element spacing and the total number of elements.

This paper details an effective method to extract dielectric parameters including dielectric constant Dk and loss tangent Df from transmission lines containing rough conductor surface. The concept of effective conductivity is firstly introduced to model conductor surface roughness in transmission lines. By using differential extrapolation method, propagation parameters of transmission lines can be extracted by removing the roughness effects. A curve-fitting method based on Genetic Algorithm (GA) is adopted to fit the propagation parameters in the smoothened case and to derive the dielectric parameters. The proposed method is especially accurate for parameter extraction at high frequency and is practical to all types of transmission lines.

The temperature performances of GaInNAs-based semiconductor devices, for next generation communication networks and photonic integrated circuits, are investigated. In particular, GaInNAs-GaInAs Multi Quantum Well active ridge waveguides, patterned with a periodic one-dimensional grating and an active defective region placed in the central layer, have been designed for efficient active optical switches and modulators. The switching mechanism was obtained around the Bragg wavelength λ≌1.2896 μm at room temperature T=298 K by properly designing the periodic grating and changing the injected current density from JOFF=0 mA/μm² to JON=0.496 mA/μm². The proposed device exhibits high performances in terms of crosstalk, contrast ratio, and modulation depth. The temperature performance of the proposed device is analyzed in the range T=298 K - 400 K, showing a good stability of the figures of merit: crosstalk CT, contrast ratio CR, and bandwidth Δλ. In particular, the CT varies at about 1.2 dB in the whole temperature range, whereas CR and Δλ experience, respectively, a maximum variation of 25% and 30% of their maximum values.

A novel microstrip diplexer with high selectivity and isolation performance is proposed through the combination of two compact bandpass filters composed of open/shorted lines and an open stub, which are designed for LTE application. Six transmission zeros in the upper stopband are used to suppress the harmonic of the microstrip diplexer. The transmission zeros near the passband can be adjusted conveniently by only changing the electrical length of the open/shorted stubs. A diplexer prototype with two passbands at 1.8 GHz and 2.1 GHz is fabricated. The isolation between the two channels is greater than 40 dB from 0.1 to 6.5 GHz.

The compressed sensing (CS) based imaging methods for tomography SAR perform well in the case of large number of baselines. Unfortunately, for the current tomography SAR, the baselines are obtained from many multi-pass acquisitions on the same scene, which is expensive and can be severely affected by temporal decorrelation. In order to reduce the number of baselines, a novel strategy for tomography SAR imaging by introducing the block-sparsity theory into the imaging processing is proposed in this paper. Using neighboring pixels information in reconstruction, the proposed method can overcome the imaging quality limitation imposed by the low number of baselines. The results with simulation data under the additive gaussian noise case are presented to verify the effectiveness of the proposed method.

This paper investigates the performance of a Windowing Based Crest Factor Reduction (CFR_WB) technique, to enhance the power efficiency of Radio Frequency (RF) power amplifiers. In particular, CFR_WB is implemented on a Doherty Power Amplifier (DPA) in conjunction with Generalized Memory Polynomial (GMP_DPD), and Volterra series based Digital Predistortion (V_DPD) techniques. Key features like spectral regrowth, Peak to Average Power Ratio (PAPR) reduction, efficiency improvement and Error Vector Magnitude (EVM) have been used to measure the efficacy of the proposed method. Both simulation and experimental results show that the proposed combination of CFR_WB technique with GMP_DPD and V_DPD is able to reduce the PAPR of the complex input signals by nearly 60%, with minimal degrading of the EVM and spectral regrowth. Moreover, such signal with reduced PAPR can be used to overdrive the DPA, allowing for a relevant average efficiency enhancement (i.e., up to 25%), while fulfilling the requirements of modern communication standards such as Wideband Code Division Multiple Access (WCDMA) and long-term evolution (LTE).

In this paper, a Rectangular Dielectric Resonator Antenna (RDRA) with a modified feeding line is designed and investigated at 28 GHz. The modified feed line is designed to excite the DR with relative permittivity of 10 which contributes to a wide bandwidth operation. The proposed single RDRA has been fabricated and mounted on a RT/Duroid 5880 (ε_r=2.2 and tan δ=0.0009) substrate. The optimized single element has been applied to array structure to improve the gain and achieve the required gain performance. The radiation pattern, impedance bandwidth and gain are simulated and measured accordingly. The number of elements and element spacing are studied for an optimum performance. The proposed antenna obtains a reflection coefficient response from 27.0 GHz to 29.1 GHz which cover the desired frequency band. This makes the proposed antenna achieve 2.1 GHz impedance bandwidth and gain of 12.1 dB. Thus, it has potential for millimeter wave and 5G applications.

Single-layer circularly polarized (CP) reflectarrays in the Ka-band are presented in this paper. Three reflectarray (RA) models are designed and measured, using geometrically dissimilar elements. Each element is analyzed individually and optimized to obtain good performance within the operating frequency band. To compensate the spatial delay from feed to the elements at RA surface, the angular rotation technique has been employed for obtaining reflected phase curve. The performances of the antennas are analyzed at 30 GHz, exhibiting 13.3% of 1.5 dB gain bandwidth, while the axial ratio bandwidth is less than 3 dB in the whole operating band.

An approach of reducing Mutual Coupling between two patch antennas is proposed in this paper. Here, a meander line resonator is placed in between the radiating elements. By inserting the meander line resonator between the patch antennas with the edge-to-edge distance less than λ/18, about 8 dB reduction of Mutual Coupling throughout the 10-dB bandwidth has been achieved without degrading the radiation pattern.The circuit model of the proposed configuration is carried out in this paper and envelope correlation coefficient is also computed. The proposed structure has been fabricated and measured.

In this paper, the uniaxial anisotropic perfectly matched layer (UPML) absorbing boundary condition in unconditionally stable five-step locally one-dimensional finite-difference time-domain (LOD5-FDTD) method is deduced. The UPML absorbing boundary condition (ABC) is validated based on comparison with a simulation in larger domain (and thus without reflection) in the first test. Then using a sinusoidal source, target field phase distribution surrounded by the UPML-ABC is analyzed. The results further illustrate the stability and efficiency of the UPML absorbing boundary condition.

This paper presents the theoretical framework for a new technique in the field of linear antenna arrays with amplitude control called error coefficient matrix. First of all, the array factor is expressed as a summation of contribution from the elements of the array. It will be shown that for small errors in excitation amplitude, the error in the overall radiation pattern at a given angle is a summation of errors contributed by the individual elements of the array at that angle. An error coefficient matrix is proposed, and its properties are discussed in great detail. The accuracy of the proposed method is investigated for varying levels of errors in weights and for varying number of error elements, using Monte-Carlo simulation. Finally, the applications of this new technique in the field of antenna arrays are presented.