2018-02-28
Power Density Evaluation of a Novel Double-Stator Magnetic Geared Permanent Magnet Generator
By
Progress In Electromagnetics Research B, Vol. 80, 19-36, 2018
Abstract
This paper presents the power density evaluation and power mapping performance of a novel magnetic geared double-stator permanent magnet generator (DSPMG) which is proposed to address problems of mechanical geared generators for low-speed power generation applications. The operating principle is based on three PM rotors consisting of prime permanent-magnet (PM) poles in the middle rotor and field PM poles in the inner and outer rotors respectively. To evaluate the power density performance, a 2-D finite-element method (FEM) is used to predict the performance of the generator, and a demonstrator prototype is fabricated and evaluated experimentally. The power density characteristics of the proposed generator are analyzed and reported. The measured results agree closely with the simulated ones to verify the validity of the magnetic geared generator design. Finally, a measurable comparison is conducted with other published prototype magnetic gear machines to demonstrate its benefits of higher power density and smaller volume size.
Citation
Shehu Salihu Mustafa, Norhisam Misron, Mohammad Lutfi Othman, and Tsuyoshi Hanamoto, "Power Density Evaluation of a Novel Double-Stator Magnetic Geared Permanent Magnet Generator," Progress In Electromagnetics Research B, Vol. 80, 19-36, 2018.
doi:10.2528/PIERB17102303
References

1. Li, X., K. Chau, M. Cheng, and W. Hua, "Comparison of magnetic-geared permanent-magnet machines," Progress In Electromagnetics Research, Vol. 133, 177-198, 2013.
doi:10.2528/PIER12080808        Google Scholar

2. Johnson, M., M. Gardner, and H. Toliyat, "Design and analysis of an axial flux magnetically geared generator," IEEE Transactions on Industry Applications, Vol. 53, No. 1, 97-105, 2017.
doi:10.1109/TIA.2016.2603962        Google Scholar

3. Oshiumi, T., N. Niguchi, and K. Hirata, "Experiment of 1 kW class magnetic-geared generator," Journal of the Japan Society of Applied Electromagnetics and Mechanics, Vol. 22, No. 2, 183-188, 2014.
doi:10.14243/jsaem.22.183        Google Scholar

4. Niu, S., K. Chau, J. Jiang, and C. Liu, "Design and control of a new double-stator cup-rotor permanent-magnet machine for wind power generation," IEEE Transactions on Magnetics, Vol. 43, No. 6, 2501-2503, 2007.
doi:10.1109/TMAG.2007.893713        Google Scholar

5. Niu, S., K. Chau, and C. Yu, "Quantitative comparison of double-stator and traditional permanent magnet brushless machines," Journal of Applied Physics, Vol. 105, No. 7, 07F105, 2009.
doi:10.1063/1.3067512        Google Scholar

6. Jian, L. and K. Chau, "Design and analysis of a magnetic-geared electronic-continuously variable transmission system using finite element method," Progress In Electromagnetics Research, Vol. 107, 47-61, 2010.
doi:10.2528/PIER10062806        Google Scholar

7. Liu, C., K. Chau, and Z. Zhang, "Novel design of double-stator single-rotor magnetic-geared machines," IEEE Transactions on Magnetics, Vol. 48, No. 11, 4180-4183, 2012.
doi:10.1109/TMAG.2012.2201705        Google Scholar

8. Niu, S., S. Ho, and W. Fu, "A novel double-stator double-rotor brushless electrical continuously variable transmission system," IEEE Transactions on Magnetics, Vol. 49, No. 7, 3909-3912, 2013.
doi:10.1109/TMAG.2013.2248347        Google Scholar

9. Wang, Q., S. Niu, S. Ho, W. Fu, and S. Zuo, "Design and analysis of novel magnetic flux-modulated mnemonic machines," IET Electric Power Applications, Vol. 9, No. 7, 469-477, 2015.
doi:10.1049/iet-epa.2014.0388        Google Scholar

10. Zhu, Z. and D. Howe, "Influence of design parameters on cogging torque in permanent magnet machines," IEEE Transactions on Energy Conversion, Vol. 15, No. 4, 407-412, 2000.
doi:10.1109/60.900501        Google Scholar

11. Atallah, K. and D. Howe, "A novel high-performance magnetic gear," IEEE Transactions on Magnetics, Vol. 37, No. 4, 2844-2846, 2001.
doi:10.1109/20.951324        Google Scholar

12. El-Refaie, A., "Fractional-slot concentrated-windings synchronous permanent magnet machines: Opportunities and challenges," IEEE Transactions on Industrial Electronics, Vol. 57, No. 1, 107-121, 2010.
doi:10.1109/TIE.2009.2030211        Google Scholar

13. Ishikawa, T., S. Shinagawa, and N. Kurita, "Analysis and failure diagnosis of squirrel-cage induction motor with broken rotor bars and end rings," IEEJ Journal of Industry Applications, Vol. 2, No. 6, 292-297, 2013.
doi:10.1541/ieejjia.2.292        Google Scholar

14. Hanafy, H., T. Abdo, and A. Adly, "2D finite element analysis and force calculations for induction motors with broken bars," Ain Shams Engineering Journal, Vol. 5, No. 2, 421-431, 2014.
doi:10.1016/j.asej.2013.11.003        Google Scholar

15. Wang, R., L. Bronn, S. Gerber, and P. Tlali, "An axial flux magnetically geared permanent magnet wind generator," IEEJ Transactions on Electrical and Electronic Engineering, Vol. 10, S123-S132, 2015.
doi:10.1002/tee.22173        Google Scholar

16. Jian, L., K. Chau, and J. Jiang, "A magnetic-geared outer-rotor permanent-magnet brushless machine for wind power generation," IEEE Transactions on Industry Applications, Vol. 45, No. 3, 954-962, 2009.
doi:10.1109/TIA.2009.2018974        Google Scholar

17. Tlali, P., S. Gerber, and R. Wang, "Optimal design of an outer-stator magnetically geared permanent magnet machine," IEEE Transactions on Magnetics, Vol. 52, No. 2, 1-10, 2016.
doi:10.1109/TMAG.2015.2487886        Google Scholar