volume | PIER Journals

Abstract

This paper reports material selection methodology for radio frequency - micro electro mechanical systems (RF-MEMS) switches used for reconfigurable antennas. As there are variety of materials available to design engineer, a proper technique to select the best possible material is needed. Three primary performance indices, pull-in voltage, RF-loss, and thermal residual stress, are used to obtain the desired performance. The selection chart shows that aluminum is the most suitable material for being used as bridge material in RF-MEMS switches to provide the best performance in reconfigurable antenna.

1. Cetiner, B. A., G. R. Crusats, L. Jofre, and N. Bıyıklı, "RF MEMS integrated frequency reconfigurable annular slot antenna," IEEE Trans. Antennas Propag., Vol. 58, No. 3, 626-632, 2010.
doi:10.1109/TAP.2009.2039300 Google Scholar

2. Jung, C. W., M. J. Lee, and F. D. Flaviis, "Reconfigurable dual-band antenna with high frequency ratio (1.6 : 1) using MEMS switches," Electronics Letters, Vol. 44, No. 2, 76-77, 2008.
doi:10.1049/el:20082349 Google Scholar

3. Cheng, S., P. Rantakari, R. Malmqvist, C. Samuelsson, T. Vaha-Heikkila, A. Rydberg, and J. Varis, "Switched beam antenna based on RF MEMS SPDT switch on quartz substrate," IEEE Antennas Wireless Propag. Lett., Vol. 8, 383-386, 2009.
doi:10.1109/LAWP.2009.2018712 Google Scholar

4. Cheng, C. C., B. Lakshminarayanan, and A. Abbaspour-Tamijani, "A programmable lens-array antenna with monolithically integrated MEMS switches," IEEE Trans. Microw. Theory Tech., Vol. 57, No. 8, 1874-1884, 2009.
doi:10.1109/TMTT.2009.2025422 Google Scholar

5. Jung, C. W. and M. J. Lee, "Reconfigurable scan-beam single-arm spiral antenna integrated with RF-MEMS switches," IEEE Trans. Antennas Propag., Vol. 54, No. 2, 455-463, 2006.
doi:10.1109/TAP.2005.863407 Google Scholar

6. Srikar, V. T. and S. M. Spearing, "Material selection for microfabricated electrostatic actuators," Sens Actuators A, Vol. 102, 279-285, 2003. Google Scholar

7. Rao, R. V., "A material selection model using graph theory and matrix approach," Materials Science and Engineering, Vol. 431, 248-255, 2006.
doi:10.1016/j.msea.2006.06.006 Google Scholar

8. Roth, R., F. Field, and J. Clark, "Multi-attribute utility analysis," Journal of Computer-Aided Materials Design, Vol. 1, No. 3, 325-342, 1994.
doi:10.1007/BF00712855 Google Scholar

9. Guisbiers, G., E. Herth, B. Legrand, N. Rolland, T. Lasri, and L. Buchaillot, "Materials selection procedure for RF-MEMS," Microelectronic Engineering, Vol. 87, 1792-1795, 2010.
doi:10.1016/j.mee.2009.10.016 Google Scholar

10. Ashby, M. F., Materials Selection in Mechanical Design, 2nd Edition, Butterworth-Heinemann, Oxford, UK, 1999.

11. Puyal, V., D. Dragomirescu, C. Villeneuve, J. Ruan, P. Pons, and R. Plana, "Frequency scalable model for MEMS capacitive shunt switches at millimeter-wave frequencies," IEEE Trans. Microw. Theory Tech., Vol. 57, No. 11, 2824-2833, 2009.
doi:10.1109/TMTT.2009.2032473 Google Scholar

12. Ekkels, P., X. Rottenberg, R. Puers, and H. A. C. Tilmans, "Evaluation of platinum as a structural thin film material for RF-MEMS devices ," J. Micromech. Microeng., Vol. 19, 065010-065018, 2009.
doi:10.1088/0960-1317/19/6/065010 Google Scholar

13. Palego, C., J. Deng, Z. Peng, S. Halder, J. C. M. Hwang，D. I. Forehand, D. Scarbrough, and C. L. Goldsmith, "Robustness of RF MEMS capacitive switches with molybdenum membranes," IEEE Trans. Microw. Theory Tech., Vol. 57, No. 12, 3262-3269, 2009.
doi:10.1109/TMTT.2009.2033885 Google Scholar

14. Alam, A. H. M. Z., M. R. Islam, S. Khan, N. B. Mohd Sahar, and N. B. Zamani, "Effects of MEMS material on designing a multi-band reconfigurable antenna," Iranian Journal Of Electrical and Computer Engineering, Vol. 8, No. 2, 112-118, 2009. Google Scholar

15. Reddy, G. P. and N. Gupta, "Material selection for microelectronic heat sinks: An application of the Ashby approach," Materials and Design, Vol. 31, 113-117, 2010.
doi:10.1016/j.matdes.2009.07.013 Google Scholar

16. Rebeiz, G. M., RF MEMS: Theory, Design, and Technology, 3rd Edition, John Wiley & Sons Inc., New Jersey, 2003.

17. Callister, W. D., Material Science and Engineering: An Introduction, 7th edition, John Wiley & Sons Inc., New York, 2007.

18. Kingsley, N., D. E. Anagnostou, M. Tentzeris, and J. Papapolymerou, "RF MEMS sequentially reconfigurable sierpinski antenna on a flexible organic substrate with novel DC-biasing technique," J. Microelectromech. Syst., Vol. 16, No. 5, 1185-1192, 2007.
doi:10.1109/JMEMS.2007.902462 Google Scholar

19. Reines, I., B. Pillans, and G. M. Rebeiz, "Thin-film aluminum RF MEMS switched capacitors with stress tolerance and temperature stability," J. Microelectromech. Syst., Vol. 20, No. 1, 193-202, 2011.
doi:10.1109/JMEMS.2010.2090505 Google Scholar

20. Dai, C.-L. and J.-H. Chen, "Low voltage actuated RF microme-chanical switches fabricated using CMOS-MEMS technique," Microsyst. Technol., Vol. 12, 1143-1151, 2006.
doi:10.1007/s00542-006-0243-7 Google Scholar

Dr. Ashish Kumar Sharma

Dr. Navneet Gupta