Ring resonators are very commonly used for the design of frequency selective surfaces (FSSs). But, for some particular design, the spacing between the resonators becomes very small. So it leaves no space to shift the reflection band towards the lower side of the spectrum. It also becomes very difficult to realize large PCBs. In this paper, an improvised design of the ring resonator using stubs is reported. This provides the designer with some flexibility. Two different configurations using this concept have been fabricated. Measured results are compared with the configuration using conventional ring resonators. These results indicate good performance with tune-ability in the response without major change in the design or in the substrate.
Venkataraman Veragur Srinivasan,
"Frequency Selective Surface with Improvised Ring-Resonator for Flexible Design," Progress In Electromagnetics Research C,
Vol. 56, 137-144, 2015. doi:10.2528/PIERC15011905
1. Lee, S. W., "Scattering by dielectric-loaded screen," IEEE Trans. Antennas Propag., Vol. 19, No. 5, 656-665, 1971. doi:10.1109/TAP.1971.1140010
2. Montgomery, J. P., "Scattering by an infinite periodic array of thin conductors on a dielectric sheet," IEEE Trans. Antennas Propag., Vol. 23, No. 1, 70-75, 1975. doi:10.1109/TAP.1975.1141006
3. Agrawal, V. D. and W. A. Imbriale, "Design of a Cassegrain sub-reflector," IEEE Trans. Antennas Propag., Vol. 27, No. 4, 466-473, Jul. 1979. doi:10.1109/TAP.1979.1142119
4. Parker, E. A. and S. M. A. Hamdy, "Rings as elements for frequency selective surface," Electron. Lett., Vol. 17, No. 17, 612-614, 1981. doi:10.1049/el:19810430
5. Mittra, R., C. H. Chan, and T. A. Cwik, "Techniques for analyzing frequency selective surfaces-a review," Proceedings of IEEE, Vol. 76, No. 12, 1593-1615, Dec. 1988. doi:10.1109/5.16352
6. Huang, J., T. K. Wu, and S. W. Lee, "Tri-band frequency selective surface with circular ring element," IEEE Trans. Antennas Propag., Vol. 42, No. 2, 166-174, Feb. 1994. doi:10.1109/8.277210
7. Wu, T. K. and S. W. Lee, "Multiband frequency-selective surface with multiring patch elements," IEEE Trans. Antennas Propag., Vol. 42, No. 11, 1484-1490, Nov. 1994.
8. Munk, B. A., Frequency Selective Surfaces: Theory and Design, John Wiley & Sons, 2000. doi:10.1002/0471723770
9. Baisakhiya, S., R. Sivasamy, M. Kanagasabai, and S. Periaswamy, "Novel compact UWB frequency selective surface for angular and polarization independent operation," Progress In Electromagnetics Research Letters, Vol. 40, 71-79, 2013. doi:10.2528/PIERL13022707
10. Yao, X., M. Bai, and J. Miao, "Equivalent circuit method for analyzing frequency selective surface with ring patch in oblique angles of incidence," IEEE Antennas and Wireless Propagation Letters, Vol. 10, 820-823, 2011.
11. Orta, R., P. Savi, and R. Tascone, "Multiple frequency-selective surfaces consisting of ring patches," Electromagnetics, Vol. 15, No. 4, 417-426, 1995. doi:10.1080/02726349508908430
12. Taylor, P. S., E. A. Parker, and J. C. Batchelor, "An active annular ring frequency selective surface," IEEE Trans. Antennas Propag., Vol. 59, No. 9, 3265-3271, Sept. 2011. doi:10.1109/TAP.2011.2161555
13. Xu, R. R., H. C. Zhao, Z. Y. Zong, and W. Wu, "Dual-band capacitive loaded frequency selective surfaces with close band spacing," IEEE Microwave and Wireless Components Letters, Vol. 18, No. 12, 782-784, Dec. 2008. doi:10.1109/LMWC.2008.2007697
14. CST Microwave Studio, Computer Simulation Technology, v. 12.1.