2017-11-08
Utilization of Low Computational Cost Two Dimensional Analytical Equations in Optimization of Multi Rings Permanent Magnet Thrust Bearings
By
Progress In Electromagnetics Research M, Vol. 62, 51-63, 2017
Abstract
Replacement of conventional bearings by passive magnetic bearings for highspeed applications, in terms of their performance will be effective, if the design is carried out by optimizing the geometrical dimensions in the given control volume. Present work deals with modification and utilization of two-dimensional (2D) analytical equations in optimization of multi rings permanent magnet (PM) thrust bearing configurations. Conventional and rotational magnetized direction (RMD) configurations are selected in optimizing the design variables for maximum bearing characteristics in a given volume with a constant aspect ratio. The design variables chosen for optimization are axial offset of rotor, number of rings, radial air thickness and inner diameter of the rotor and stator PM rings. MATLAB codes for solving 2D equations are developed in optimizing configuration variables. Further, optimized parameter values of the two configurations are compared. Finally, optimized results obtained using 2D and three-dimensional (3D) equations for the conventional configuration with same aspect ratio are compared, and conclusions are presented.
Citation
Siddappa Iranna Bekinal, Mrityunjay Doddamani, and Nikhil D. Dravid, "Utilization of Low Computational Cost Two Dimensional Analytical Equations in Optimization of Multi Rings Permanent Magnet Thrust Bearings," Progress In Electromagnetics Research M, Vol. 62, 51-63, 2017.
doi:10.2528/PIERM17072007
References

1. Bekinal, S. I., T. R. Anil, and S. Jana, "Analysis of axially magnetized permanent magnet bearing characteristics," Progress In Electromagnetics Research B, Vol. 44, 327-343, 2012.
doi:10.2528/PIERB12080910        Google Scholar

2. Bekinal, S. I., T. R. Anil, S. Jana, S. S. Kulkarni, A. Sawant, N. Patil, and S. Dhond, "Permanent magnet thrust bearing: Theoretical and experimental results," Progress In Electromagnetics Research B, Vol. 56, 269-287, 2013.
doi:10.2528/PIERB13101602        Google Scholar

3. Ravaud, R. and G. Lemarquand, "Halbach structures for permanent magnets bearings," Progress In Electromagnetic Research M, Vol. 14, 263-277, 2010.
doi:10.2528/PIERM10100401        Google Scholar

4. Earnshaw, S., "On the nature of the molecular forces which regulate the constitution of the luminiferous ether," Transactions of the Cambridge Philosophical Society, Vol. 7, 97-112, 1842.        Google Scholar

5. Sotelo, G. G., R. Andrade, and A. C. Ferreira, "Magnetic bearing sets for a flywheel system," IEEE Trans. on Applied Super Conductivity, Vol. 17, No. 2, 2150-2153, 2007.
doi:10.1109/TASC.2007.899268        Google Scholar

6. Fang, J., Y. Le, J. Sun, and K. Wang, "Analysis and design of passive magnetic bearing and damping system for high-speed compressor," IEEE Trans. Magn., Vol. 48, No. 9, 2528-2537, 2012.
doi:10.1109/TMAG.2012.2196443        Google Scholar

7. Morales, W., R. Fusaro, and A. Kascak, "Permanent magnetic bearing for spacecraft applications," Tribology Transactions, Vol. 46, No. 3, 460-464, 2003.
doi:10.1080/10402000308982651        Google Scholar

8. Tian, L.-L., X.-P. Ai, and Y.-Q. Tian, "Analytical model of magnetic force for axial stack permanent-magnet bearings," IEEE Trans. Magn., Vol. 48, No. 10, 2592-2599, 2012.
doi:10.1109/TMAG.2012.2197635        Google Scholar

9. Bekinal, S. I. and S. Jana, "Generalized three-dimensional mathematical models for force and stiffness in axially, radially, and perpendicularly magnetized passive magnetic bearings with `n' number of ring pairs," ASME Journal of Tribology, Vol. 138, No. 3, 031105(1–9), 2016.        Google Scholar

10. Moser, R., J. Sandtner, and H. Bleuler, "Optimization of repulsive passive magnetic bearings," IEEE Trans. Magn., Vol. 42, No. 8, 2038-2042, 2006.
doi:10.1109/TMAG.2005.861160        Google Scholar

11. Yoo, S. Y., et al. "Optimal design of non-contact thrust bearing using permanent magnet rings," Int. Journal of Precision Engg. and Manufacturing, Vol. 12, No. 6, 1009-1014, 2011.
doi:10.1007/s12541-011-0134-4        Google Scholar

12. Lijesh, K. P. and H. Hirani, "Development of analytical equations for design and optimization of axially polarised radial passive magnetic bearing," ASME Journal of Tribology, Vol. 137, 011103(1–9), 2015.        Google Scholar

13. Bekinal, S. I., M. R. Doddamani, and S. Jana, "Optimization of axially magnetised stack structured permanent magnet thrust bearing using three dimensional mathematical model," ASME Journal of Tribology, Vol. 139, No. 3, 031101(1-9), 2017.
doi:10.1115/1.4034533        Google Scholar

14. Beneden, M. V., V. Kluyskens, and B. Dehez, "Optimal sizing and comparison of permanent magnet thrust bearings," IEEE Trans. Magn., Vol. 53, No. 2, 2017.        Google Scholar