volume | PIER Journals

Abstract

In this paper, the effect of corrosion on the magnetic behavior of a magnetic material used as a magnetic circuit in the induction machines is studied. With this objective, the magnetic properties of the samples with corrosion and without corrosion were evaluated by the study of hysteresis loops using a homemade vibrating sample magnetometer (VSM). The magnetic parameters extracted from the hysteresis loops such as saturation magnetization, coercive, remanent magnetization, squareness ratio, magnetic permeability, and hysteresis area were analyzed. It was shown that more energy is required to demagnetize the sample with corrosion than the sample without corrosion, and the hysteresis loss in the case of the sample with corrosion is more than the case of the sample without corrosion. These mean that when the corrosion is presented in the magnetic circuits of the induction machine, the hysteresis loss increases, consequentially reducing the machine efficiency.

1. Agamloh, E. B., "Induction motor efficiency," IEEE Industry Applications Magazine, Vol. 17, No. 6, 20-28, 2011.
doi:10.1109/MIAS.2011.942298 Google Scholar

2. Aminu, M., P. Barendse, and A. Khan, "Efficiency estimation of induction machines using nonintrusive no-load low voltage test," 2017 IEEE Energy Conversion Congress and Exposition (ECCE), 3171-3178, 2017.
doi:10.1109/ECCE.2017.8096577 Google Scholar

3. Verucchi, C. J., R. Ruschetti, and G. Kazlauskas, "High efficiency electric motors: Economic and energy advantages," IEEE Latin America Transactions, Vol. 11, No. 6, 1325-1331, 2013.
doi:10.1109/TLA.2013.6710379 Google Scholar

4. Al-Badri, M. and P. Pillay, "Evaluation of measurement uncertainty in induction machines efficiency estimation," 2014 IEEE International Conference on Power and Energy (PECon), 288-292, 2015. Google Scholar

5. Misir, O., S. M. Raziee, N. Hammouche, C. Klaus, R. Kluge, and B. Ponick, "Prediction of losses and efficiency for three-phase induction machines equipped with combined Star-Delta windings," IEEE Transactions on Industry Applications, Vol. 53, No. 4, 3579-3587, 2017.
doi:10.1109/TIA.2017.2693958 Google Scholar

6. Dominguez, J. R., C. Mora-Soto, S. Ortega-Cisneros, J. J. R. Panduro, and A. G. Loukianov, "Copper and core loss minimization for induction motors using high-order sliding-mode control," IEEE Transactions on Industrial Electronics, Vol. 59, No. 7, 2877-2889, 2012.
doi:10.1109/TIE.2011.2171170 Google Scholar

7. Gmyrek, Z., A. Boglietti, and A. Cavagnino, "Estimation of iron losses in induction motors: Calculation method, results, and analysis," IEEE Transactions on Industrial Electronics, Vol. 57, No. 1, 161-171, 2010.
doi:10.1109/TIE.2009.2024095 Google Scholar

8. Roy, R., K. K. Prabhakar, and P. Kumar, "Core-loss calculation in different parts of induction motor," IET Electric Power Applications, Vol. 11, No. 9, 1664-1674, 2017.
doi:10.1049/iet-epa.2017.0369 Google Scholar

9. Dems, M. and K. Komeza, "The influence of electrical sheet on the core losses at no-load and full-load of small power induction motors," IEEE Transactions on Industrial Electronics, Vol. 64, No. 3, 2433-2442, 2017.
doi:10.1109/TIE.2016.2587817 Google Scholar

10. Liang, Y., X. Bian, H. Yu, and C. Li, "Finite-element evaluation and eddy-current loss decrease in stator end metallic parts of a large double-canned induction motor," IEEE Transactions on Industrial Electronics, Vol. 62, No. 11, 6779-6785, 2015.
doi:10.1109/TIE.2015.2438051 Google Scholar

11. Yamazaki, K. and W. Fukushima, "Loss analysis of induction motors by considering shrink fitting of stator housings," IEEE Transactions on Magnetics, Vol. 51, No. 3, 2015. Google Scholar

12. Cheaytani, J., A. Benabou, A. Tounzi, M. Dessoude, L. Chevallier, and T. Henneron, "End-region leakage fluxes and losses analysis of cage induction motors using 3-D finite-element method," IEEE Transactions on Magnetics, Vol. 51, No. 3, 2015.
doi:10.1109/TMAG.2014.2365355 Google Scholar

13. Liang, Y.-P., Y.-L. Hu, X. Liu, and C.-X. Li, "Calculation and analysis of can losses of canned induction motor," IEEE Transactions on Industrial Electronics, Vol. 61, No. 9, 4531-4538, 2014.
doi:10.1109/TIE.2013.2290762 Google Scholar

14. Abshinova, M., "Factors affecting magnetic properties of Fe-Si-Al and Ni-Fe-Mo alloys," Procedia Engineering, Vol. 76, 35-44, 2014.
doi:10.1016/j.proeng.2013.09.245 Google Scholar

15. O’Handley, R. C., Modern Magnetic Materials: Principles and Investigations, Wiley Interscience, 2000.

16. Mc Currie, R. A., Ferromagnetic Materials Structure and Properties, Academic Press, 1994.

17. Shirakata, Y., N. Hidaka, M. Ishitsuka, A. Teramoto, and T. Ohmi, "High permeability and low loss Ni-Fe composite material for high-frequency applications," IEEE Transactions on Magnetics, Vol. 44, No. 9, 2100-2106, 2008.
doi:10.1109/TMAG.2008.2001073 Google Scholar

Dr. M'hamed Ouadah

Dr. Omar Touhami

Dr. Rachid Ibtiouen

Dr. Mohammed Khorchef

Dr. Djilali Allou